Building a Patio Using Concrete Pavers

By Mark J. Donovan

Last year I put in a patio underneath my elevated deck using concrete pavers. The patio overlooks the shores of Lake Winnipesaukee in central New Hampshire and makes a great outdoor living space for getting out of the sun and reading a book or surfing the net.

The particular concrete pavers I used came in 3 or 4 shapes and had a slightly washed out look, which was the look I was aiming for.

To install a patio using concrete pavers, we had to initially remove the existing dirt and replace it with several inches of sand. We then compacted the sand and then began the process of laying out the concrete pavers.

The concrete pavers were installed such that we went back and back filled in the required cut pieces of concrete pavers. After completing the installation of concrete pavers, we then swept in more sand to fill in the gaps and create a rigid patio surface.

Once the concrete paver patio was complete we backfilled around it with topsoil, planted some grass seed, and began enjoying our new outdoor living space.

Sanding a Deck with a Palm Sander

Sanding Deck Edges with a Palm Sander is Slow and Tedious

By Mark J. Donovan

Due to the fact that it rained shortly after I put a coat of deck sealer on my deck back two years ago, I have found myself sanding my deck to restore its look and to prepare it for a deck stain. If I can offer one word of advice, it is to make sure there is no rain in the forecast for at least 24 hours before applying a deck sealer. My deck remained tacky for months and the sealer began to peel as soon as it finally dried.

I used an orbital floor sander on the main body of the deck to remove the old deck sealer, however I have had no choice but to use a small palm sander on the deck edges. Though it is working it is a slow process.

I am using the same 36 grit sandpaper that I did on the main body of the deck. As a matter of fact, I am using the same pieces of sandpaper. I have simply cut small wedges out of them to fit the palm sander. The palm sander has a surface area of about 4”x4”.

With a little luck I will wrap up the deck sanding today and will stain it when there is a 24 hour window of dry weather. Unfortunately, in the northeast lately dry weather is as rare as a blue moon. I’ll keep my fingers crossed.

Where is Summer?

By Mark J. Donovan

Yesterday when I was closing the front door to my home it dawned on me that I have yet to swap out the glass panel with the screen panel on my storm door. I also remembered that I have yet to install the window air conditioners. That’s how cool and rainy it has been here in New Hampshire for the past month or so.

One cannot help but question the theory of “Global Warming” when on the last day of June, you realize that the last time you experienced a warm summer day was last September. Could we be entering a “Global Cooling” period? With a sample size of only a few months, relative to the billions of years that Earth has existed, it would be almost as irresponsible as the suggestion of Global Warming based on a few decades of data. Instead, it is probably just as accurate to say that we have hit a period of rainy bad luck, or are experiencing the weather oscillations effects of El Nino or La Nina.

Whatever the case, it is time for me to install the screen in the storm door, and put in the air conditioners. If I have learned anything in life, it is that change is constant and that one day I will wake up to a hot, sultry morning in the not too distant future. And who knows, I may find out that I won’t be pulling out the air conditioners until mid October this year.

Let’s keep our fingers crossed for some warm, summer weather to arrive soon.

Eliminate Squeaky Door Hinges

By Mark J. Donovan

Squeaky door hinges can be a real annoyance, however with 5 minutes of work you can eliminate them.

To start with, make sure the hinges are all fastened tightly to the door frame using a screw driver.

Next, remove one hinge pin at a time from each door hinge and wipe it clean with a rag. To remove the hinge pin you will need a hammer and small thin screwdriver. Just slide the thin screwdriver into the base of the hinge, underneath the hinge pin and tap it up and out with your hammer.

Now, lubricate the hinge pin with a little oil or WD40. You can even use Canola oil in a pinch.

Next, lubricate the door hinge itself with a little WD40 or oil and wipe it clean with a rag. Note, make sure you place a rag underneath the door hinges before applying any oil to the door hinge. Otherwise you may leave an oil stain on your flooring.

Slide the hinge pin back into the door hinge and repeat this process for the other remaining hinges.

With any luck your door should be squeak free after lubricating all of the hinges.

Will 3-way light bulbs work with a Dimmer Switch?

3-Way Light Bulbs and Dimmer Switches

By Mark J. Donovan

3-way light bulbs are constructed with 2 filaments in then. The filaments operate at different wattages. 3-way light bulbs work in special lamps that are designed to control which filament(s) are turned on in a 3-way light bulb. When the lamp is switched once the lowest wattage filament is turned on to create a dim light. When the lamp is switched a second time just the highest wattage filament is turned on to create a medium light. When the filament is switched a third time both filaments are turned on creating maximum light.

With a wall dimmer switch there is no way to send a command to the special 3-way light bulb lamp fixture to switch between the different filament settings. As a result the 3-way light bulb effectively does not work with a dimmer switch. In addition, having a 3-way light bulb in a dimmer switch is pointless since the dimmer switch itself will control the level of the brightness.

When using a 3-way light bulb in a lamp that is connected to a dimmer switch all that the dimmer switch will do is control the brightness level for the particular filament setting the lamp is set to.